( 5 : 1 ) a a b b c c d d e e f f a a b b c c d d 15-00070 o conec abc dim. in mm r date drawn inventor 10 t h i s d r a w i n g m a y n o t b e c o p i e d o r r e p r o d u c e d i n a n y w a y , a n d m a y n o t b e p a s s e d o n t o a t h i r d p a r t y w i t h o u t w r i t t e n p e r m i s s i o n . o w n e r s h i p a n d c o p y r i g h t o f c o n e c g m b h d-old norm appd. tolerance material: title: dwg no: din- sh: part no: name date name description rev. d o n o t a l t e r c a d d r a w i n g b y h a n d scale: customer approval date: name: title: company name: approval # freigabe # deblocage # autorizacion # approval a p p r o v a l # f r e i g a b e # d e b l o c a g e # a u t o r i z a c i o n approval # freigabe # deblocage # autorizacion approval # freigabe # deblocage # autorizacion # approval 15K1A273 a3 1 d-sub female hd see notes schmidt 08.09.08 15.09.08 fischer 26pos. solder cup with hexlocking screw 2:1 (5:1) 15-00070 aorigin 3 x b ? 3129 26.09.08 petker 3 x c ? 3435 01.10.09 hs notes: 1. recommended solder instruction see sheet 2 2. ip rating: ip 67 3. sealed to withstand pressure up to 1,45 psi for 30 minutes after soldering 4. metalshell: zinc die cast; min. 50in nickel plating over copper 5. insulators: pbt gf ul 94 v-0, black 6. o-ring: silicone per astm d2000 70 shore a 7. sealing compound: epoxy resin ul 94 v-0; black 8. contacts: copper alloy plating (see part no): o please add 1 for 30in hard gold over min. 50in nickel o please add 3 for 8in hard gold over min. 50in nickel solder cup accepts cable awg 22 9. hexlocking screws: stainless steel 10. recommended panel cut-out on sheet 2 11. recommended torque for mounting screw 35ncm (3.1 in.lb) / max.67ncm (6 in.lb) 12. connector is part marked: 15-00070 o conec abc b b at all times water resistant connectors not in use should be covered with a conec water resistant cap or water tight hood. c c b c 24,79 - 0,25 0 + 33,32 - 0,12 0,13 + 47,7 - 0 0,3 + 2 1 , 1 - 0 0 , 3 + o-ring 4-40 unc 4-40 unc see note 12 8 - 0,23 0,02 + 6 , 1 3 - 0 , 0 8 0 , 1 7 + 3 , 6 - 0 0 , 2 5 + o (see note 8) 1 2 - 0 , 3 0 , 4 + sealing compound 1,04 n (26x) 9 , 5 - 0 , 3 0 , 4 + 1 0 4 , 6 9 , 4 4,8 sw
a a b b c c d d e e f f a a b b c c d d dim. in mm r date drawn inventor 10 t h i s d r a w i n g m a y n o t b e c o p i e d o r r e p r o d u c e d i n a n y w a y , a n d m a y n o t b e p a s s e d o n t o a t h i r d p a r t y w i t h o u t w r i t t e n p e r m i s s i o n . o w n e r s h i p a n d c o p y r i g h t o f c o n e c g m b h d-old norm appd. tolerance material: title: dwg no: din- sh: part no: name date name description rev. d o n o t a l t e r c a d d r a w i n g b y h a n d scale: customer approval date: name: title: company name: approval # freigabe # deblocage # autorizacion # approval a p p r o v a l # f r e i g a b e # d e b l o c a g e # a u t o r i z a c i o n approval # freigabe # deblocage # autorizacion approval # freigabe # deblocage # autorizacion # approval 15K1A273 a3 2 panel cut-out see sheet 1 schmidt 08.09.08 15.09.08 fischer d-sub female hd 26pos. solder cup with hexlocking screw 5:1 see sheet 1 aorigin 2 x b ? 3129 26.09.08 petker b b 3 , 4 r ` 0 , 1 3 1 1 , 4 ` 0 , 1 28,8 ` 0,1 3 , 1 ` 0 , 0 5 n ( 2 x ) i 0,26 b i 0,26 a 1 0 ` 1 33,32 ` 0,1 b a recommended panel cut-out solder instruction 1. cable should be prepared for soldering. the cable/wires must be pretinned. 2. insert cable/wire into solder cup. 3. operate the soldering iron at 350c, 50 watt max. and use a pencil tip. 4. put tip to wire in solder cup. 5. after 1 second bring in solder. 6. heat for 3 seconds longer. do not heat contact more than 4 seconds in total. 7. remove soldering iron. 8. wait until solder gets rigid again. 9. do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up.
|
